APS997C INSTALLATION MANUAL PDFMarch 25, 2020
Model APSC. Owners 24 Hour Timed Start Setup, Operation, and Use 23 of this manual has a section for the particular features and options installed in. Save this Book to Read prestige apsc installation manual PDF eBook at our Online Library. Get prestige apsc installation manual PDF. AUDIOVOX APSC INSTALLATION MANUAL — | PDF | 73 Pages | KB | 09 AUDIOVOX APSC INSTALLATION MANUAL The key.
|Published (Last):||23 September 2005|
|PDF File Size:||12.17 Mb|
|ePub File Size:||9.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
Aps c Installation Manual
By pressing ‘print’ button you will print only current page. This wire will be routed to the vehicle ECM tach janual or through the inwtallation into the engine compartment and connect to the negative side of the ignition coil. Page 19 Monitoring The Vehicle’s Engine: Don’t have an account? Page 29 b 29 of Cut this wire and connect the ignition cylinder side to chassis ground. The Superheterodyne Instsllation Antenna Assembly provided with this unit allows routing from below the dash board for maximum operating range.
Add to my manuals Add. In this case, connect the Light Blue Wire to terminal 86 of a external relay. Monitoring The Vehicle’s Engine: Page 16 These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface. Fuses must be used and located as close as possible to the power source for adequate protec- tion of the vehicle.
This is accomplished by first mapping out installstion firing order of the engine in groups of as indicated below.
PLATINUM APSC INSTALLATION MANUAL Pdf Download.
Comments to this Manuals Your Name. If this wire is not used or you have difficulty accessing the glow plug preheat circuit, you may elect to utilize the Diesel timed output as specified in Remote Start feature selection 9. This is a normally opened starter cut arrangement, when power is removed from the security system, the starter disable feature will remain operational, and the vehicle will not start. Page 18 Connector Port The 4 pin port located on mznual side of this module is for proprietary Audiovox data bus interface modules.
Platinum APS-997C Installation Manual
See owners manual for turning this feature on from the transmitter. Be certain that the chosen mounting majual will not inhibit any of the controls of the vehicle.
Page 26 The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below. Don’t show me this message again.
Page 30 For technical support go to www. Page 10 12 White Wire: Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay.
Got it, continue to print. Once activated, the unit will start 1 time if the manuall temperature reaches “0 ” and then will run the allotted time. Page 11 ground trigger output wire of motion detectors, microwave detectors, or glass break detectors, can be connected to this Light Green trigger input wire. After you instwllation confirmed the operation of the Audiovox Remote Start unit and tested all the safety features qps997c the system: Special considerations must be made for windshield glass installatiom some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception.
Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay. Do not remove the fuse holders from this wire harness. Manual Override Safety Testing and Operation. Installation Insfallation The Major Components. After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system: Connect this wire to the vehicle’s parking light feed wire.
Page of 28 Go. Page 12 21 Light Blue Wire: If the vehicle’s parking lights are ground switched, connect this wire to chassis ground. Connector Port The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules.
Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in personal injury and property damage. This is a normally opened starter cut arrangement, when power is manaul from the secu- rity system, the starter disable feature will remain operational, and the vehicle will not start.
Route this wire through a grommet in the firewall to the siren location. Temperature Start Programming And Aps99c7. Page 25 To decrease sensitivity, turn the adjustment screw counter clockwise. The unit will monitor the voltage level of the battery during remote start, wait for the voltage to drop while cranking, then look for the voltage level to go above the level it was before the vehicle began to crank which indicates the vehicle is running.
If the vehicle has delay interior lights, and you wish to avoid three chirp, defect zone, indication normally associated with this type of interior light, we suggest you learn the interior light delay. The mounting location selected must be within 24″ To connect to the key in sensor circuit as shown for method 2: This unit has the ability to learn the dome light delay time, up to 60 seconds. You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you’ve made the changes you wanted in Bank 2, Siren two Long ChirpYou can also go right to bank 3 by: This wire will show 0 volts when the key is turned to the “OFF” Connect the Red wire to the low current ground signal wire from the factory door lock switch to the factory door lock relay.
In most cases, the Purple wire will need to be connected to only one door switch no matter how many doors the vehicle has as most door lighting circuits are wired in parallel. Parking Light Flasher Output This wire is the normally open contact of the on board parking light flash relay.